LIDECO Standard Parts 07/2022

F364 Technical data: Hose: Hose fittings: Polyamide 11, black, dimpled Free cutting steel, zinc-plated Measuring couplings: Adapter: Free cutting steel, zinc-plated Steel, burnished 630 bar Max. permi. pressure: Temperature range: 0–100°C Technical data: Hose: Hose fittings: Adapter: Polyurethane/polyamide, black, dimpled Steel, zinc-plated Steel, zinc-plated 380 bar Max. permi. pressure: Temperature range: 0–100°C Technical data: Hose: Hose fittings: Adapter: Polyurethane/polyamide, black, dimpled Steel, zinc-plated Steel, zinc-plated 315 bar Max. permi. pressure: Temperature range: 0–100°C Technical data: Hose: Hose adapter: Adapter: Max. permi. pressure: Temperature range: Conduit: Polyamide 11, black, dimpled Free cutting steel, zinc-plated Steel, zinc-plated 475 bar 0 to +80°C Steel ∅4 mm ∅2 mm 430 bar External conduit diameter (da): Internal conduit diameter (di): max. dynamic pressure: Temperature range: 0 to +100°C Note: Pipe system, 24° conus micro for higher temps on request. GAS SPRINGS - CONNECTOR SYSTEMS GENERAL Connecting gas springs in one more systems enables the user to monitor gas spring pressure from outside the tool, to adjust it if necessary, to fill it and to drain it. The connector system has many advantages including ease of maintenance, reliability and improvement in the quality of gas spring use in the tool. FIBRO offers four different systems for hose connections for gas springs: Minimess system, Compression fitting system, JIC system (24° flare) and Micro connector system. The hoses, screwed connectors and other components are selected to meet the most stringent standards and undergo a series of tests including service life, static steel and robustness after repeated assembly and disassembly.. + mall external hose diameter ∅5 mm + mall bending radius Rmin = 20 + igh pressure resistance + Vibration-proof measurement couplings + Connector with valve + o tools needed for connecting hose to adapter, and disconnecting ± Swaged non-detachable hose fitting – ot for use with a pressure reservoir + Assemble on-site system + Reusable hose fitting + igh pressure resistance ± Suitable for connecting to a pressure reservoir under certain conditions – arger bending radius Rmin = 40 – Not suitable for gas springs with M6 connection thread – xtra time required for preparing hose and fitting it + uitable for connecting to a pressure reservoir + ide range of connection adapters + ibration-proof (O-ring seal) + igh pressure resistance ± Swaged non-detachable hose fitting – arger bending radius Rmin = 40 –Not suitable for gas springs with M6 connection thread + mall external hose diameter ∅5 mm + lexible pipe: small bending radius Rmin = 20 mm + ipe: Min. bending radius = 12 mm (3x da) + igh pressure resistance + small connection fitting + ibration-proof due to O-ring seal + swaged non-detachable hose fitting - ot for use with a pressure reservoir - limited suitability for gas springs with thread connection G 1 / 8 Minimess-system 2480.00.23./24. Cutting ring system 2480.00.10. 24°-cone-system 2480.00.25./26. Connector system, 24° conus micro 2480.00.27./28. Recommended application: Most commonly used system for all gas springs with G 1 / 8 gas connection. Not suitable for use with a pressure reservoir due to small internal diameter (reduced flow volume). Recommended application: For all gas springs with G 1 / 8 gas connection. Mainly used for self-assembly in small numbers. Recommended application: For all gas springs with G 1 / 8 gas connection. Mainly used for connection to pressure reservoir. Recommended application: For gas springs with M6 gas connection. Not suitable for use with a pressure reservoir due to small internal diam- eter (reduced flow volume).